Chosen Solution I bought a new carb and tune-up kit and replaced the old ones. I pulled the gas tank to check for any leaks. I replaced the gas cap. It starts right up and revs up to speed only to half throttle, anything past half throttle it bogs down dies. After I let it run for a bit and shut it down the hose that has the breather end leaks gas all over the place....
Chosen Solution Just took out of the box for the first time and followed all the directions and steamer heats up but no steam comes out of the hose. Have check hose and other troubleshooting per user manual, nothing works. Help please . @nclement1996 if you just purchased this and followed the instructions and it still does not work, my suggestion would be to contact customer support either from where you purchased it or the manufacturer....
Chosen Solution I have here a recent Kenwood HB890 handblender that suddenly stopped working. When I opened up the blender I found a soldered fuse that was blown (3,15A slow 250V, I’m in Europe by the way). Replaced the fuse but when testing the blender it blew the fuse again and what’s more, I saw a spark coming out of the motor (still had it out of the housing). I then soldered a jumper wire instead of a fuse and took out my variac to test it at a lower input voltage (tested at 140V, remember I’m in Belgium where mains are 230V)....
Chosen Solution I have a warranty on my tablet where do I send it to get it check or get a new one lalylove8 that will depend on where you bought it and where you are located. In the US you could go here for more support. Do you know what company you’re tablet is from? That’s will be more helpful to know. And have you tried getting a new charger for the tablet?...
Chosen Solution ok how do i fully factory reset my system setting and none of my app are even working what do i do Here is the way to perform that reset. You will lose all data on the device looks like if you perform the full clean option. https://rcasupport.zendesk.com/hc/en-us/…
Chosen Solution Ok, so I dropped my I pad mini. And I broke the inside of the screen cause there is a hardly noticeable green line at the corner of the I pad, and there are no cracks in the outside. I also have this grayish bar on the side of my I pad that sometimes changes colors, which is making the lighting of my I pad really dim and I can hardly see....
Chosen Solution I dropped my Kindle Fire in water. It was for only a moment. I grabbed and wiped it down. Now, what should I do? Hi @candycatie As you know water and electronics and electricity are not a good mix. The impurities in the water causes corrosion and provides circuit paths for the electricity which were not in the tablet’s operating design and could damage the components. The corrosion process starts immediately and continues until it has been cleaned properly First do not turn on your tablet and then you need to remove the battery as soon as possible from the tablet to minimize further damage....
Chosen Solution So I dropped my phone in a river. Took it to a repair place that dried it out, said the only problem is the daughterboard for the sound broke. I can accept calls, but I can’t hear anything in the call. ditto with music, videos etc. They offered a repair for $80, but I was hoping for a cheaper fix. Any suggestions? If I was to attempt to do this repair myself, I’d buy a replacement back cover too as they are likely to be damaged whilst removing from the M7....
Chosen Solution I have a iMac 2011 27", EMC 2429, 2.7GHz, MC813LL/A, and I’m having problems. First one was the display shutting down randomly, likely due to the common problem with this iMac that Apple did recall here. After days of research, I found the most common fix (after the recall expired) was to actually take the faulty GPU and bake in the oven. Many articles and YouTube videos available here....
Chosen Solution When i turn the tv on it will turn off what can be the cause of that @sugamama bad power capacitors on the power supply can cause that. However, there are plenty of other things that can do the same. You got to start somewhere, so you might as well remove the back (unplug your TV) and take a look (don’t touch) on the power supply. Check for domed, leaking caps....
Chosen Solution I have a imac that does not boot; the startup chime comes up every 2 or 3 seconds and the display is black. I don’t have the boot disk. Pls recommend fixes that I can try myself. I unplugged the cable and attached it. there are no other devices connected to it now. Zap the PRAM; hold down CMD+OPT+P+R while turning on the machine, keep it held down until you hear the third startup chime, then release and see if it boots....
Chosen Solution Hello everyone. Tell me please. I have an iMac 2019 ‘27. I put a normal m2 SSD and one 8tb HDD there instead of Fusiondrive. Now I would like to remove the HDD and put two m2 disks instead. Is it possible? If it is impossible to install two, is it possible to install one? If this is also impossible, does anyone know a box for two m2 but without a power supply?...
Chosen Solution I have an iPhone 5s and the home button is completely dead. It clicks, but does nothing else. I know that if I replace the home button, I will lose the touch id funtionality, because a chip on the original button is paired to the motherboard. My questions are: Where is this chip located?Is there any way to move it to the new button? Thanks in advance for any anwers!...
Chosen Solution sorry for my english, please reply or iphone 6 32GB made in 2017 have a fix problem with touch dissease, or it’s still the same iphone as in 2014. Thanks for the reply Any iPhone 6 and iPhone 6 plus is prone to touch disease. The current theory is putting the phone into your back pocket and sitting on the phone is the root issue. The phone flexes and over time the connections snap within the logic board....
Chosen Solution i got iphone 6 which is having bootloop problem , as usual i tried to restore but it is not detecting by itunes , after visual inspection i found someone has worked on tristar , i change tristar with new one still it is not detecting by pc ,tried with another frame , new lcd , good known battery, still same issue ,please help with this Check all the pads below the trister is not a complete for USB there is also a other parts from USB connector to trister ....
Chosen Solution Hi, my iPhone 6S does not get any service, there’s always the “No Service” message there, although the SIM card is recognized. The phone is factory unlocked though. Só mundo question is, will this be fixed if I replace the Upper Left Antenna? Hello, I might not give much help in this area but I do know that this is most commonly a chip failure or a damaged trace on the motherboard of the device....
Chosen Solution I just had a customer inside my store, I have heard and fixed multiple ghost touching, but this one has typed messages (random) and sent pictures to randoms on messenger.. Does anyone know if a new screen would solve this issue? My guess is that the “home” button is going faulty or is sticking. I have the same issue with an iPad Mini 2 that has a finicky home button and will run thru menus at times like it is being operated by a ghost....
Chosen Solution Hello everyone Recently I bought iPhone X from the second hand. I wanted to transfer files from pc to iPhone and pc didn’t recognized it, I tapped on “Trust“, removed passcode and tried it in recovery mode but still nothing. It charges only when I plug the charger when iPhone is booting but when I plug the charger when it is booted it didn’t charge. And also iPhone will only boot up with pluged in charger but when iphone boots up i can remove charger....
Chosen Solution i replaced the lcd / digitizer on the iPod because it was cracked and the iPod touch worked completely fine before now i have the screen all hooked up and nothing shows up on the screen and it won’t show up on my computer and i checked that power/volume flex cable and everything looked fine Your ipod would still show up on the computer with a bad flex cable....
Chosen Solution Is the charge port connected to the mother board? its connects to the motherboard via fpc connector so if you need to change it unplug the old 1 and plug in the new 1 Phones nowadays should have their Micro USB socket attached to a separate board for easier repairs.
